Transactions of Nonferrous Metals Society of China (中国有色金属学报)•2026•DOI: 10.1016/S1003-6326(26)67065-3
Polycrystalline LiNi0.8Co0.1Mn0.1O2 (NCM811) cathodes undergo intergranular cracking and structural collapse during extended cycling, limiting their commercial viability. This study reports single-crystalline NCM811 synthesized via a rapid ethanol–water solvothermal method. The solvothermal duration was varied, and the 60 min sample (NCM-60) exhibited optimal electrochemical performance. X-ray diffractometry confirmed an α-NaFeO2 structure with R-3m space group and high crystallinity. NCM-60 delivered a reversible capacity of 157.28 mA·h/g at 1C and a capacity retention of 55.06% after 200 cycles, significantly outperforming polycrystalline NCM (PC-NCM). Cross-sectional scanning electron microscopy revealed no apparent cracks in NCM-60 after 200 cycles, whereas PC-NCM exhibited severe intergranular fracture. The results demonstrate that shortening solvothermal time reduces precursor particle size and crystallinity, but 60 min yields the best balance. Pre-oxidation of the carbonate precursor before lithiation is recommended to mitigate CO2 evolution and lithium–nickel disorder during high-temperature sintering. This rapid solvothermal route offers a scalable pathway to single-crystal NCM811 with enhanced cycling stability and mechanical integrity.
Transactions of Nonferrous Metals Society of China (中国有色金属学报)•2026•DOI: 10.1016/S1003-6326(26)67067-7
Conventional ammonium sulfate leaching of ionic rare earth ores generates 4–6 t of ammonia-nitrogen wastewater per ton of rare earth and drives mining-area soil pH to 3.5–4.0, creating an acute environmental compliance risk. This study evaluates a low-ammonium synergistic lixiviant comprising 0.020 mol/L (NH4)2SO4 and 0.010 mol/L acetic acid (HAc) at pH 4–5, 30 °C, and 1 h contact time. Comparative leaching experiments establish a rare earth element (REE) leaching efficiency of 88.92%, a 13.36% absolute increase over single 0.020 mol/L (NH4)2SO4 leaching. To achieve the same ~90% efficiency benchmark, the conventional single-salt system requires 0.030 mol/L (NH4)2SO4; the synergistic system therefore reduces ammonium consumption by 33.3%. Surface characterization indicates a dual mechanism: H+ attenuates electrostatic interactions between RE3+ and silicate surfaces, enhancing NH4+–RE3+ exchange, while CH3COO− forms soluble RE3+/Al3+ complexes that prevent Al(OH)3 passivation and sustain surface reactivity. The protocol offers a directly deployable route to cut reagent cost and ammonia-nitrogen load without sacrificing recovery, addressing the principal bottleneck restraining sustainable ionic rare earth ore exploitation under China's dual-carbon and rare earth total-amount control policies.
Transactions of Nonferrous Metals Society of China (中国有色金属学报)•2026•DOI: 10.1016/S1003-6326(26)67056-2
A coupled three-dimensional cellular automata (CA) model was employed to predict hydrogen porosity in Al−Si alloy castings as a function of thermal boundary conditions. Simulations quantified porosity distribution across cooling rates from 0.25 to 50 °C/s at an initial hydrogen content of 3.0×10−3 mL/g, generating a comprehensive porosity defect database. Four machine learning algorithms—support vector machine (SVM), random forest (RF), K-nearest neighbors (KNN), and gradient boosting machine (GBM)—were trained and compared for each porosity characteristic to identify the optimal model. For porosity percentage prediction, the KNN model achieved a determination coefficient (R2) of 0.94, root mean square error (RMSE) of 0.035, and mean absolute error (MAE) of 0.022 on the test set. Experimental validation via optical microscopy confirmed that average equivalent porosity diameter and porosity percentage predictions fell within 20% error. The model demonstrates superior performance compared to single nonlinear function fits and other simulation approaches, offering a pathway to reduce simulation time while enhancing prediction accuracy for porosity size distribution in large casting components. The database and coupled CA-ML framework provide a robust tool for mapping porosity defects in industrial Al−Si castings, addressing a critical need for reliable quality control in automotive and aerospace applications.
Nano Research•2026•DOI: 10.26599/FRICT.2025.9441207
Wear debris particles critically influence frictional interfaces. Conventional understanding holds that debris accumulation causes severe wear. However, debris from metal friction pairs includes anti-wear metal oxides generated by tribochemical reactions, which can form a protective oxidation film to resist wear. Minimizing abrasive damage from accumulated debris and exploiting the anti-wear property of metal oxides are mutually exclusive. Here, a rational design of a bioinspired coupling surface (BCS) that manipulates nanoscale wear debris to resist further wear is reported. The BCS comprises surface textures that capture and temporarily store excess nanoscale wear debris, and a deposited self-cleaning coating that subsequently transfers part of the captured debris back into the sliding-contact interface, where it converts into a protective oxidation film. The coexistence of these two elements with contrasting properties in manipulating nanoscale wear debris considerably reduces wear under water lubrication, oil lubrication, and macroscale superlubricity. Specifically, the wear rate of steel is reduced by 50.4%, 51.2%, and 46.3% under these respective conditions. This strategy achieves the manipulation and utilization of wear debris for anti-wear purposes, promoting further investigation into the role of nanoscale wear debris and its utilization approaches.
Journal of Semiconductors (半导体学报 - 中国科学院半导体研究所)•2026•DOI: 10.1088/1674-4926/25090014
Enhanced low dose rate sensitivity (ELDRS) and pre-irradiation elevated-temperature stress (PETS) effects were investigated in four commercial bipolar integrated circuits. Irradiations spanned dose rates from 0.002 to 50 rad(Si)/s, and PETS treatments were conducted at 250 °C and 400 °C. For specific devices, radiation-induced degradation at 0.002 rad(Si)/s exceeded that at 0.01 rad(Si)/s by more than a factor of three. The maximum PETS enhancement factor reached 20.3. Devices exhibiting PETS effects consistently showed an ELDRS saturation dose rate (SDR) below 0.01 rad(Si)/s, whereas those with SDR above 0.1 rad(Si)/s did not exhibit PETS. Material analysis revealed that devices with SDR < 0.01 rad(Si)/s had higher hydrogen content in their passivation layers, and those with PETS effects had elevated double hydrogen bond concentrations. The ultra-low dose rate ELDRS is attributed to the transport of H+ released from hydrogen-containing defects in the passivation layer to the Si/SiO2 interface during irradiation. The PETS effect arises primarily from the transport of H2 into the oxide layer; this H2 is released by N–H2 and Si–H2 in the passivation layer after elevated-temperature treatment and further releases H+ through reactions with oxide trap charges during irradiation. These findings establish a direct link between passivation layer chemistry and radiation response, providing critical data for reliability assessment of commercial-off-the-shelf bipolar devices in space applications.
Int. Journal of Mining Science and Technology (采矿与安全工程)•2026•DOI: 10.1016/j.ijmst.2026.01.001
In igneous-intruded coal seams, coal undergoes significant metamorphism, which critically alters its pore structure and oxygen consumption dynamics, thereby elevating its spontaneous combustion tendency. This study investigates the specific surface area, pore volume, structure complexity/connectivity, heterogeneity/local features of pore size distribution, and oxygen consumption dynamics of igneous metamorphic coal through N2/CO2 isothermal adsorption tests and low-temperature oxidation experiments, and elucidates the influence mechanisms of pore structure evolution on oxygen consumption dynamics during low-temperature oxidation. With increasing metamorphic degree, igneous metamorphic coal exhibits a more pronounced reduction in specific surface area during oxidation, while the increase in structure complexity due to coal-oxygen reactions is suppressed. Thermally metamorphic coal demonstrates accelerated oxygen consumption, with oxidation amplifying the difference in reaction rates compared to raw coal. Key mechanisms include oxidation-induced reduction in mesopore complexity and micropore volume, decreased dominance of small-pore-volume apertures, and increased heterogeneity, collectively leading to a lower half-oxygen-consuming temperature and steeper oxygen consumption curves. Simultaneously, increased pore volume/complexity and reduced uniformity/connectivity act synergistically to enhance oxygen consumption capacity, highlighting the coupling between pore structure evolution and oxidation behavior in igneous metamorphic coal. This study provides theoretical insights into the pore-oxygen coupling mechanisms governing coal spontaneous combustion in igneous intrusion areas.
Int. Journal of Mining Science and Technology (采矿与安全工程)•2026•DOI: 10.1016/j.ijmst.2026.03.004
The energy-driven progressive brittle shear failure of rock joints is a key mechanism behind deep engineering disasters such as joint-induced rockbursts and engineering earthquakes. To investigate the energy evolution mechanisms and disaster proneness, monotonic and stepwise loading-unloading tests were performed on regular dentate joints under constant normal stiffness boundary conditions. Results indicate a transition in damage mechanism from climbing wear of low-inclination asperities to brittle rupture of high-inclination ones, accompanied by a marked decrease in irreversible displacement. Energy analysis reveals a strong linear relationship between pre-peak elastic energy density and both input energy density and shear stress squared. The post-peak elastic energy release rate (g) and the self-sustaining instability coefficient (l) increase with joint undulation. A dimensionless brittleness index (BI) integrating the complete energy conversion and release process was proposed to quantify the energy balanced budget. The highly undulated joint R4 showed the most pronounced brittleness and instability intensity with the highest BI value of 0.697, along with g = 0.774 and l = 0.611. This study provides deeper insight into the understanding of the disaster-inducing proneness and stability assessment in jointed rock mass.
Journal of Semiconductors (半导体学报 - 中国科学院半导体研究所)•2026•DOI: 10.1088/1674-4926/26030014
Helical trilayer graphene (HTG) with equal twist angles in the same rotational sense has been predicted to reconstruct into triangular domains with opposite Chern numbers, giving rise to topological boundary modes. This work reviews the direct imaging of the supermoiré landscape in HTG using a scanning single-electron transistor (SET) probe that maps local inverse compressibility dμ/dn. The device comprises an HTG stack encapsulated in hexagonal boron nitride (hBN) with a graphite back gate for electrostatic doping. Linecuts of dμ/dn reveal uniform, weakly dispersive incompressible peaks at moiré filling factors ν = ±1 for a twist angle θ ≈ 1.45°, corresponding to a moiré wavelength λM ≈ 10 nm. These peaks indicate that within individual domains the lattice relaxes into a well-ordered moiré pattern. At larger length scales, the interference between multiple moiré patterns produces a supermoiré modulation with period λSM ≈ 380 nm, forming a mosaic of two inequivalent domain types due to local C2z symmetry breaking. The ratio of experimental to theoretical area Aexp/Ath and the strain parameter ε = 1 − cosθ are extracted, providing quantitative metrics for lattice relaxation. The findings establish SET as a powerful tool for characterizing relaxation and topological order in twisted multilayers, with implications for moiré-based quantum devices.
China Foundry•2026•DOI: 10.1007/s41230-026-5163-9
In laser powder bed fusion (LPBF) additive manufacturing, surface depressions caused by melt pool instability can induce defects throughout the layer-by-layer printing process. To address the limited understanding of interlayer defect transmission mechanisms, synchrotron X-ray in situ imaging was used to systematically investigate the dynamic evolution of surface depressions during multi-pass printing by adjusting interlayer process parameters. Experimental results show that insufficient energy input in the first layer leads to balling and fracture of melt tracks. When the energy input in the second layer is increased, local overheating at the gap between melt tracks from the previous layer causes surface depressions. Reducing the energy input in the third layer hinders melt backflow, enlarging the depression region. Further lowering the energy input in the final layer leads to the formation of internal unfused defects. This study reveals the dynamic correlation between surface depressions and interlayer defect evolution, offering critical experimental evidence and theoretical guidance for closed-loop interlayer process control in laser additive manufacturing.
Nano-Micro Letters (纳微快报)•2026•DOI: 10.1007/s40820-025-01895-x
Co3S4 electrocatalysts with mixed valences of Co ions and excellent structural stability possess favorable oxygen evolution reaction (OER) activity, yet challenges remain in fabricating rechargeable lithium-oxygen batteries (LOBs) due to their poor OER performance, resulting from poor electrical conductivity and overly strong intermediate adsorption. In this work, fancy double heterojunctions on 1T/2H-MoS2@Co3S4 (1T/2H-MCS) were constructed derived from the charge donation from Co to Mo ions, thus inducing the phase transformation of MoS2 from 2H to 1T. The unique features of these double heterojunctions endow the 1T/2H-MCS with complementary catalysis during charging and discharging processes. It is worth noting that 1T-MoS2@Co3S4 could provide fast Co–S–Mo electron transport channels to promote ORR/OER kinetics, and 2H-MoS2@Co3S4 contributed to enabling moderate eg orbital occupancy when adsorbed with oxygen-containing intermediates. On the basis, the Li2O2 nucleation route was changed to solution and surface dual pathways, improving reversible deposition and decomposition kinetics. As a result, 1T/2H-MCS cathodes exhibit an improved electrocatalytic performance compared with those of Co3S4 and MoS2 cathodes. This innovative heterostructure design provides a reliable strategy to construct efficient transition metal sulfide catalysts by improving electrical conductivity and modulating adsorption toward oxygenated intermediates for LOBs.
Journal of Central South University•2026•DOI: 10.1007/s11771-026-6264-8
Aiming at the problem of large deformation of arch shoulder in deep high stress roadway of Hudi Coal Mine, through field sampling, experimental test and numerical simulation, the deformation mechanism of arch shoulder under the coupling action of high stress, soft and hard rock strata of roof, weakening of surrounding rock and disturbance of space staggered roadway was revealed. According to the research results, high-stress increases the range of the plastic zone, and the soft and hard rock strata change the expansion form of the plastic zone. With the decrease of the vertical distance of the space staggered roadway, the insufficient bearing capacity of the supporting material and other factors lead to the increase of the deformation of the shoulder angle and the side, forming the deformation characteristics of the arch shoulder. Based on this, the active and passive collaborative control technology is proposed, and the targeted support concept of "unloading control + strong support + collaborative" is adopted. The optimization scheme controls the deformation of roadway within 8% of the section size, significantly reduces the range of the plastic zone, and effectively solves the problem of difficult support of arch shoulder deformation.
Journal of Central South University•2026•DOI: 10.1007/s11771-026-6265-7
A porous wollastonite ceramic with high porosity and low density has been successfully fabricated at low temperature with silicate tailings and electrolytic manganese slag (MS) as primary raw materials in this study. The influences of calcination temperature, SiC, and MS addition amounts on porosity, water adsorption, pore size distribution, bulk density, and bending strength were systematically studied. The results showed that 0.4 wt% of SiC was optimal for the ceramic foaming at a sintering temperature of 1140 ℃. The porosity of ceramics reduced from 78.4% to 63.7%, bulk density elevated from 0.96 to 1.13 g/cm3, and bending strength increased from 8.43 to 11.22 MPa as the MS increased from 8.33 wt% to 41.67 wt%. Moreover, the best corrosion resistance performance was reached to 99.55% with 8.33 wt% MS content and a sintering temperature of 1160 ℃. This work is of significance for the solid waste utilization.
Nano-Micro Letters•2025•DOI: 10.1007/s40820-025-01724-1
Soft electronics, which are designed to function under mechanical deformation (such as bending, stretching, and folding), have become essential in applications like wearable electronics, artificial skin, and brain-machine interfaces. Crystalline silicon is one of the most mature and reliable materials for high-performance electronics; however, its intrinsic brittleness and rigidity pose challenges for integrating it into soft electronics. Recent research has focused on overcoming these limitations by utilizing structural design techniques to impart flexibility and stretchability to Si-based materials, such as transforming them into thin nanomembranes or nanowires. This review summarizes key strategies in geometry engineering for integrating crystalline silicon into soft electronics, from the use of hard silicon islands to creating out-of-plane foldable silicon nanofilms on flexible substrates, and ultimately to shaping silicon nanowires using vapor–liquid–solid or in-plane solid–liquid–solid techniques. We explore the latest developments in Si-based soft electronic devices, with applications in sensors, nanoprobes, robotics, and brain-machine interfaces. Finally, the paper discusses the current challenges in the field and outlines future research directions to enable the widespread adoption of silicon-based flexible electronics.
Nano-Micro Letters•2025•DOI: 10.1007/s40820-025-01718-z
Pressure sensors are essential for a wide range of applications, including health monitoring, industrial diagnostics, etc. However, achieving both high sensitivity and mechanical ability to withstand high pressure in a single material remains a significant challenge. This study introduces a high-performance cellulose hydrogel inspired by the biomimetic layered porous structure of human skin. The hydrogel features a novel design composed of a soft layer with large macropores and a hard layer with small micropores, each of which contribute uniquely to its pressure-sensing capabilities. The macropores in the soft part facilitate significant deformation and charge accumulation, providing exceptional sensitivity to low pressures. In contrast, the microporous structure in the hard part enhances pressure range, ensuring support under high pressures and preventing structural failure. The performance of hydrogel is further optimized through ion introduction, which improves its conductivity, and as well the sensitivity. The sensor demonstrated a high sensitivity of 1622 kPa⁻¹, a detection range up to 160 kPa, excellent conductivity of 4.01 S m⁻¹, rapid response time of 33 ms, and a low detection limit of 1.6 Pa, outperforming most existing cellulose-based sensors. This innovative hierarchically porous architecture not only enhances the pressure-sensing performance but also offers a simple and effective approach for utilizing natural polymers in sensing technologies. The cellulose hydrogel demonstrates significant potential in both health monitoring and industrial applications, providing a sensitive, durable, and versatile solution for pressure sensing.
Nano-Micro Letters•2025•DOI: 10.1007/s40820-025-01685-5
The treatment of ammonia nitrogen wastewater (ANW) has garnered significant attention due to the ecology, and even biology is under increasing threat from over discharge ANW. Conventional ANW treatment methods often encounter challenges such as complex processes, high costs and secondary pollution. Considerable progress has been made in employing solar-induced evaporators for wastewater treatment. However, there remain notable barriers to transitioning from fundamental research to practical applications, including insufficient evaporation rates and inadequate resistance to biofouling. Herein, we propose a novel evaporator, which comprises a bio-enzyme-treated wood aerogel that serves as water pumping and storage layer, a cost-effective multi-walled carbon nanotubes coated hydrophobic/hydrophilic fibrous nonwoven mat functioning as photothermal evaporation layer, and aggregation-induced emission (AIE) molecules incorporated as anti-biofouling agent. The resultant bioinspired evaporator demonstrates a high evaporation rate of 12.83 kg m−2 h−1 when treating simulated ANW containing 30 wt% NH4Cl under 1.0 sun of illumination. AIE-doped evaporator exhibits remarkable photodynamic antibacterial activity against mildew and bacteria, ensuring outstanding resistance to biofouling over extended periods of wastewater treatment. When enhanced by natural wind under 1.0 sun irradiation, the evaporator achieves an impressive evaporation rate exceeding 20 kg m−2 h−1. This advancement represents a promising and viable approach for the effective removal of ammonia nitrogen wastewater.
Nano-Micro Letters•2025•DOI: 10.1007/s40820-024-01638-4
Magnetic absorbers with high permeability have significant advantages in low-frequency and broadband electromagnetic wave (EMW) absorption. However, the insufficient magnetic loss and inherent high conductivity of existing magnetic absorbers limit the further expansion of EMW absorption bandwidth. Herein, the spinel (FeCoNiCrCu)3O4 high-entropy oxides (HEO) are successfully constructed on the surface of FeCoNiCr0.4Cu0.2 high-entropy alloys (HEA) through low-temperature oxygen bath treatment. On the one hand, HEO and HEA have different magnetocrystalline anisotropies, which is conducive to achieving continuous natural resonance to improve magnetic loss. On the other hand, HEO with low conductivity can serve as an impedance matching layer, achieving magneto-electric co-modulation. When the thickness is 5 mm, the minimum reflection loss (RL) value and absorption bandwidth (RL < −5 dB) of bi-phase high-entropy composites (BPHEC) can reach −12.8 dB and 633 MHz, respectively. The RCS reduction value of multilayer sample with impedance gradient characteristic can reach 18.34 dB m2. In addition, the BPHEC also exhibits temperature-stable EMW absorption performance, high Curie temperature, and oxidation resistance. The absorption bandwidth maintains between 593 and 691 MHz from −50 to 150 °C. This work offers a new and tunable strategy toward modulating the electromagnetic genes for temperature-stable ultra-broadband megahertz EMW absorption.
Nano-Micro Letters•2025•DOI: 10.1007/s40820-024-01585-0
Electrocatalytic urea wastewater treatment technology has emerged as a promising method for environmental remediation. However, the realization of highly efficient and scalable electrocatalytic urea wastewater treatment (SEUWT) is still an enormous challenge. Herein, through regulating the adsorption behavior of urea functional groups, the efficient SEUWT coupled hydrogen production is realized in anion exchange membrane water electrolyzer (AEMWE). Density functional theory calculations indicate that self-driven electron transfer at the heterogeneous interface (NiO/Co3O4) can induce charge redistribution, resulting in electron-rich NiO and electron-deficient Co3O4, which are superior to adsorbing C=O (electron-withdrawing group) and –NH2 (electron-donating group), respectively, regulating the adsorption behavior of urea molecule and accelerating the reaction kinetics of urea oxidation. This viewpoint is further verified by temperature-programmed desorption experiments. The SEUWT coupled hydrogen production in AEMWE assembled with NiO/Co3O4 (anode) and NiCoP (cathode) can continuously treat urea wastewater at an initial current density of 600 mA cm−2, with the average urea treatment efficiency about 53%. Compared with overall water splitting, the H2 production rate (8.33 mmol s−1) increases by approximately 3.5 times. This work provides a cost-effective strategy for scalable purifying urea-rich wastewater and energy-saving hydrogen production.
Nano-Micro Letters•2025•DOI: 10.1007/s40820-025-01674-8
Gate-all-around field-effect transistors (GAA-FETs) represent the leading-edge channel architecture for constructing state-of-the-art high-performance FETs. Despite the advantages offered by the GAA configuration, its application to catalytic silicon nanowire (SiNW) channels, known for facile low-temperature fabrication and high yield, has faced challenges primarily due to issues with precise positioning and alignment. In exploring this promising avenue, we employed an in-plane solid–liquid-solid (IPSLS) growth technique to batch-fabricate orderly arrays of ultrathin SiNWs, with diameters of DNW = 22.4 ± 2.4 nm and interwire spacing of 90 nm. An in situ channel-releasing technique has been developed to well preserve the geometry integrity of suspended SiNW arrays. By optimizing the source/drain contacts, high-performance GAA-FET devices have been successfully fabricated, based on these catalytic SiNW channels for the first time, yielding a high on/off current ratio of 10^7 and a steep subthreshold swing of 66 mV dec−1, closing the performance gap between the catalytic SiNW-FETs and state-of-the-art GAA-FETs fabricated by using advanced top-down EBL and EUV lithography. These results indicate that catalytic IPSLS SiNWs can also serve as the ideal 1D channels for scalable fabrication of high-performance GAA-FETs, well suited for monolithic 3D integrations.
Nano-Micro Letters•2025•DOI: 10.1007/s40820-024-01600-4
Reversible solid oxide cells (RSOCs) are capable of converting various energy resources, between electricity and chemical fuels, with high efficiency and flexibility, making them suitable for grid balancing and renewable energy consumption. However, the practical application of RSOCs is still limited by the insufficient activity and stability of the electrodes in different operating modes. Herein, a highly efficient symmetrical electrode composed of La0.3Sr0.6Ti0.1Co0.2Fe0.7O3−δ (LSTCF) nanofibers and in situ exsolved Co3Fe7 nanoparticles is developed for boosting the performance of RSOCs. The reversible phase transition, high activity and stability of the electrode have been confirmed by a combination of experimental (e.g., transmission electron microscopy and X-ray absorption fine structure) and computational studies. Electrolyte-supported RSOCs with the symmetrical electrode demonstrate excellent catalytic activity and stability, achieving a high peak power density of 0.98 W cm−2 in the fuel cell mode using H2 as the fuel (or 0.53 W cm−2 using CH4 as the fuel) and a high current density of 1.09 A cm−2 at 1.4 V in the CO2 electrolysis mode (or 1.03 A cm−2 at 1.3 V for H2O electrolysis) at 800 °C while maintaining excellent durability for over 100 h.
New Carbon Materials (新型炭材料)•2025•DOI: 10.1016/S1872-5805(NCM2025-5-3)
In recent years, numerous single-atom catalysts (SACs) have been synthesized to activate persulfate (PS) by a non-radical pathway because of its high selectivity, and activity for the catalyst. Metal-nitrogen-carbon (M-Nx-C) has been identified as the key active site in SACs. Although methods for preparing SACs have been extensively reported, a systematic summary of the direct construction of M-Nx-C, especially unconventional metal-nitrogen-carbon (UM-Nx-C, x≠4), on SACs for PS non-radical activation has still not been reported. The role of the M-Nx-C active sites on PS non-radical activation is discussed and methods for the formation of M-Nx-C and UM-Nx-C active sites in SACs and the effect of catalyst carriers such as carbon nitride (g-C3N4), MOFs, COFs, and other carbon materials are reviewed. Direct and indirect methods, especially for UM-Nx-C active site formation, are also elaborated. Factors affecting the formation of a M-Nx-C active site on SACs are also discussed. Prospects for the use of M-Nx-C active sites for the non-radical activation of PS by SACs to remove organic contaminants from wastewater are evaluated.
Journal of Semiconductors (半导体学报 - 中国科学院半导体研究所)•2025•DOI: 10.1088/1674-4926/25020008
In this study, we present the fabrication of vertical SnO/β-Ga2O3 heterojunction diode (HJD) via radio frequency (RF) reactive magnetron sputtering. The valence and conduction band offsets between β-Ga2O3 and SnO are determined to be 2.65 and 0.75 eV, respectively, through X-ray photoelectron spectroscopy, showing a type-Ⅱ band alignment. Compared to its Schottky barrier diode (SBD) counterpart, the HJD presents a comparable specific ON-resistances (Ron,sp) of 2.8 mΩ·cm² and lower reverse leakage current (IR), leading to an enhanced reverse blocking characteristics with breakdown voltage (BV) of 1675 V and power figure of merit (PFOM) of 1.0 GW/cm². This demonstrates the high quality of the SnO/β-Ga2O3 heterojunction interface. Silvaco TCAD simulation further reveals that electric field crowding at the edge of anode for the SBD was greatly depressed by the introduction of SnO film, revealing the potential application of SnO/β-Ga2O3 heterojunction in the future β-Ga2O3-based power devices.
China Foundry•2025•DOI: 10.1007/s41230-025-4049-6
In this work, the effects of hot isostatic pressing and heat treatment (solution and double aging) on the high-temperature tensile properties of a nickel-based polycrystalline superalloy K417G were investigated. The experimental results indicate that following the hot isostatic pressing and heat treatment, the porosity of the alloy decreases from 0.072% (in as-cast state) to 0.043%. The volume fraction of γ' phase increases from 43.28% to 56.54%, and the shape tends to be more cubic. The plasticity of the superalloy at 900 °C increases from 5.1% in as-cast state to 9.8% followed HIP and HT, but the tensile strength remains unchanged. Large size micropores are present in the as-cast sample and cracks sprout and expand at the micropores. After hot isostatic pressing and heat treatment, micropores are effectively eliminated, preventing them from becoming sources of cracks. This delay in the emergence of cracks results in enhanced plasticity. In addition, dislocations in the specimens after hot isostatic pressing and heat treatment bypasses the γ' phase through the Orowan mechanism, leading to a further increase in plasticity.
Chinese Journal of Mechanical Engineering•2025•DOI: 10.1186/s10033-025-01299-3
Shape prediction of deformable linear objects (DLO) plays critical roles in robotics, medical devices, aerospace, and manufacturing, especially in manipulating objects such as cables, wires, and fibers. Due to the inherent flexibility of DLO and their complex deformation behaviors, such as bending and torsion, it is challenging to predict their dynamic characteristics accurately. Although the traditional physical modeling method can simulate the complex deformation behavior of DLO, the calculation cost is high and it is difficult to meet the demand of real-time prediction. In addition, the scarcity of data resources also limits the prediction accuracy of existing models. To solve these problems, a method of fiber shape prediction based on a physical information graph neural network (PIGNN) is proposed in this paper. This method cleverly combines the powerful expressive power of graph neural networks with the strict constraints of physical laws. Specifically, we learn the initial deformation model of the fiber through graph neural networks (GNN) to provide a good initial estimate for the model, which helps alleviate the problem of data resource scarcity. During the training process, we incorporate the physical prior knowledge of the dynamic deformation of the fiber optics into the loss function as a constraint, which is then fed back to the network model. This ensures that the shape of the fiber optics gradually approaches the true target shape, effectively solving the complex nonlinear behavior prediction problem of deformable linear objects. Experimental results demonstrate that, compared to traditional methods, the proposed method significantly reduces execution time and prediction error when handling the complex deformations of deformable fibers. This showcases its potential application value and superiority in fiber manipulation.
Journal of Central South University•2025•DOI: 10.1007/s11771-025-6074-4
Addressing the issues of significant entry settlement and severe mining pressure manifestations in the conventional 121 approach, an innovative N00 approach is proposed. By comparing the mining process and entry formation process of different approaches, the characteristics of entry roof settlement evolution under different approaches are obtained. The N00 approach, which incorporates roof cutting and NPR cable support, optimizes the mining and entry formation process to reduce the settlement phase of entry roof, decreases the settlement of entry roof, and enhances the steadiness of entry roof. The N00 approach modifies the entry roof structure through roof cutting and establishes a hydraulic support load mechanics model for the mining panel to derive the theoretical load pressure formula for the N00 approach’s hydraulic support. Compared with the conventional 121 approach, the pressure on the N00 approach’s hydraulic support is reduced. Empirical data obtained through field monitoring demonstrate that the N00 approach has reduced the roof settlement of the entry and weakened the mining pressure manifestation at the mining panel, achieving the goal of protecting the entry and mining panel.
Journal of Central South University•2025•DOI: 10.1007/s11771-025-6071-7
Mechanical activation (MA) is a significant pretreatment technique for enhancing the dissolution of mineral; however, its promotion effect on the role of pyrite during chalcopyrite bioleaching has not been elucidated up to now. In this study, the effect of MA on the role of pyrite on chalcopyrite bioleaching mediated by Acidithiobacillus ferroxidans was investigated by X-ray diffraction, scanning electron microscopy, particle size distribution analysis, and electrochemical measurement. The results showed MA could significantly reduce the minerals particle size, and increase the specific surface area and surface energy of minerals. For example, the d50 of chalcopyrite reduced from 13.40 to 0.31 μm after MA. The copper extraction of mixed MA-chalcopyrite and MA-pyrite system was 63.4%, which exhibited a 51.8% enhancement compared to the non-activated mixed system. Electrochemical experiments identified that the strengthening effect of pyrite on chalcopyrite dissolution was negligible before MA. After MA, the dissolution mechanism of chalcopyrite was not changed, and pyrite could not only provide additional oxidants (acids and iron) but also act as the cathode in the galvanic couple. In this case, the bioleaching of chalcopyrite was accelerated. Therefore, a model of the promotion effect of mechanical activation on the role of pyrite on chalcopyrite bioleaching was proposed.
Int. Journal of Minerals, Metallurgy and Materials (矿物冶金与材料学报)•2025•DOI: 10.1007/s12613-024-3059-5
Flotation is the most common method to recover valuable minerals by selective adsorption of collectors on target mineral surfaces. However, in subsequent hydrometallurgy of mineral flotation concentrates, the adsorbed collectors must be desorbed since it can adversely affect the efficiency of metallurgical process and produce wastewater. ZL, as a fatty acid mixture, is a typical industrially used collector for scheelite flotation in China. Sodium oleate (NaOL) has similar fatty acid group as ZL. In this study, the desorption behavior of NaOL/ZL from scheelite surface by a physical method of stirring at a low temperature was investigated. NaOL desorption tests of single mineral showed that a desorption rate of 77.75% for NaOL from scheelite surface into pulp was achieved in a stirring speed of 2500 r/min at 5°C in a neutral environment. Under the above desorption condition, in the pulp containing desorbed collector by adding extra 30% normal NaOL dosage, the scheelite recovery reached about 95% in the single mineral flotation test. Desorption and reuse of ZL collector for the flotation of real scheelite ore showed only a 75% normal dosage of ZL could produce a qualified rough concentrate. The atomic force microscope (AFM) tests showed that after desorption treatment of low temperature and strong stirring, the dense strip-like structure of NaOL on the scheelite surface was destroyed to be speck-like. Molecular dynamics simulations (MDS) demonstrated that the adsorption energy between NaOL and scheelite surface was more negative at 25°C (−13.39 kcal/mol) than at 5°C (−11.50 kcal/mol) in a neutral pH, indicating that a low temperature was beneficial for the desorption of collector from mineral surface. Due to its simplicity and economy, the method we proposed of desorption of collector from mineral surface and its reuse for flotation has a great potential for industrial application.
Int. Journal of Minerals, Metallurgy and Materials (矿物冶金与材料学报)•2025•DOI: 10.1007/s12613-024-3034-1
Fe–Cr–Ni austenitic alloys are extensively utilized in the hot-end components of nuclear light water reactors, turbine disks, and gas compressors. However, their low strength at elevated temperatures limits their engineering applications. In this study, a novel precipitation-strengthened alloy system is developed by incorporating Al and Si elements into a FeCrNi equiatomic alloy. The results indicate that the FeCrNiAlxSix (at%, x = 0.1, 0.2) alloys possess heterogeneous precipitation structures that feature a micron-scale σ phase at the grain boundaries and a nanoscale ordered body-centered cube (B2) phase within the grains. An exceptional strength–ductility synergy across a wide temperature range is achieved in FeCrNiAl0.1Si0.1 alloys due to grain refinement and precipitation strengthening. Notably, a yield strength of 693.83 MPa, an ultimate tensile strength of 817.55 MPa, and a uniform elongation of 18.27% are attained at 873 K. The dislocation shearing mechanism for B2 phases and the Orowan bypass mechanism for σ phase, coupled with a high density of nano-twins and stacking faults in the matrix, contribute to the excellent mechanical properties at cryogenic and ambient temperatures. Moreover, the emergence of serrated σ phase and micro-twins in the matrix plays a crucial role in the strengthening and toughening mechanisms at intermediate temperatures. This study offers a novel perspective and strategy for the development of precipitation-hardened Fe–Cr–Ni austenitic alloys with exceptional strength–ductility synergy over a broad temperature range.
Nano-Micro Letters•2025•DOI: 10.1007/s40820-024-01570-7
Efficient and stable photocathodes with versatility are of significance in photoassisted lithium-ion batteries (PLIBs), while there is always a request on fast carrier transport in electrochemical active photocathodes. Present work proposes a general approach of creating bulk heterojunction to boost the carrier mobility of photocathodes by simply laser assisted embedding of plasmonic nanocrystals. When employed in PLIBs, it was found effective for synchronously enhanced photocharge separation and transport in light charging process. Additionally, experimental photon spectroscopy, finite difference time domain method simulation and theoretical analyses demonstrate that the improved carrier dynamics are driven by the plasmonic-induced hot electron injection from metal to TiO2, as well as the enhanced conductivity in TiO2 matrix due to the formation of oxygen vacancies after Schottky contact. Benefiting from these merits, several benchmark values in performance of TiO2-based photocathode applied in PLIBs are set, including the capacity of 276 mAh g−1 at 0.2 A g−1 under illumination, photoconversion efficiency of 1.276% at 3 A g−1, less capacity and Columbic efficiency loss even through 200 cycles. These results exemplify the potential of the bulk heterojunction strategy in developing highly efficient and stable photoassisted energy storage systems.