Transactions of Nonferrous Metals Society of China (中国有色金属学报)•2026•DOI: 10.1016/S1003-6326(26)67058-6
Twin-roll casting (TRC) Mg−3Al−1Sn−0.5Ca−0.2Mn (ATXM) alloys exhibit limited deformation resistance and inadequate corrosion performance, constraining their commercial deployment. This study integrates rare earth (RE) microalloying (Sm, Ce, or Y at 0.1 wt.%) with rolling to address the strength–plasticity–corrosion trilemma. Rolling reduces grain size from ~50 μm to below 5 μm and transforms Al8Mn5 secondary phases into Al8Mn4RE, modifying phase composition, dimension, and spatial arrangement. The rolled ATXM-0.1Y alloy achieves a yield strength of 238 MPa, tensile strength of 305 MPa, and elongation of 23%, coupled with a corrosion rate of approximately 1.7 mm/a—an ~80% reduction relative to TRC ATXM. Sm and Ce additions yield strengths of 238 and 232 MPa, elongations of 18% and 17%, and corrosion rates of 3.4 and 2.9 mm/a, respectively. Strengthening mechanisms are attributed to fine-grain and Orowan strengthening, while corrosion mitigation arises from reduced individual galvanic corrosion and enhanced protective corrosion product film quality. The work establishes a screening protocol for RE elements and processing parameters to synergistically improve mechanical and corrosion properties, facilitating commercial adoption of Mg alloys.
China Foundry•2026•DOI: 10.1007/s41230-026-5146-x
Wire-arc directed energy deposition (WA-DED) has attracted considerable attention for the fabrication of magnesium (Mg) alloys due to its high efficiency, low cost, and rapid prototyping capability for complex components. However, the inherent rapid solidification and complex thermal cycling associated with WA-DED often result in coarse columnar grains and pronounced mechanical anisotropy, which severely limiting its application potential. In this study, a novel spiral oscillation (SO) strategy was implemented during WA-DED AZ31 Mg alloy to refine the microstructure, reduce mechanical anisotropy, and achieve a strength-ductility synergy. Specifically, the yield strength (YS), ultimate tensile strength (UTS), and elongation (EL) are increased by 9.7%, 38.1%, and 147%, respectively. These improvements by the SO strategy are primarily attributed to the promotion of columnar-to-equiaxed transformation (CET), a 74.2% reduction in maximum texture intensity, and a more uniform distribution of second-phase particles. Second-phase particles are primarily composed of Al8Mn5 and Al8Mn4Y. This study provides a novel strategy for microstructural control aimed at improving the performance of WA-DED AZ31 Mg alloy components.
Nano-Micro Letters•2025•DOI: 10.1007/s40820-025-01647-x
Herein, a novel Janus-structured multifunctional membrane with integrated electromagnetic interference (EMI) shielding and personalized thermal management is fabricated using shear-induced in situ fibrillation and vacuum-assisted filtration. Interestingly, within the polytetrafluoroethylene (PTFE)-carbon nanotube (CNT)-Fe3O4 layer (FCFe), CNT nanofibers interweave with PTFE fibers to form a stable “silk-like” structure that effectively captures Fe3O4 particles. By incorporating a highly conductive MXene layer, the FCFe/MXene (FCFe/M) membrane exhibits excellent electrical/thermal conductivity, mechanical properties, and flame retardancy. Impressively, benefiting from the rational regulation of component proportions and the design of a Janus structure, the FCFe/M membrane with a thickness of only 84.9 µm delivers outstanding EMI shielding effectiveness of 44.56 dB in the X-band, with a normalized specific SE reaching 10,421.3 dB cm2 g−1, which is attributed to the “absorption-reflection-reabsorption” mechanism. Furthermore, the membrane demonstrates low-voltage-driven Joule heating and fast-response photothermal performance. Under the stimulation of a 3 V voltage and an optical power density of 320 mW cm−2, the surface temperatures of the FCFe/M membranes can reach up to 140.4 and 145.7 °C, respectively. In brief, the FCFe/M membrane with anti-electromagnetic radiation and temperature regulation is an attractive candidate for the next generation of wearable electronics, EMI compatibility, visual heating, thermotherapy, and military and aerospace applications.